POA Print on Air - How to Use

One of the weaknesses of 3D printing is definitely the printing of very inclined surfaces or areas sottosquadro.Infatti to be able to print this ...

3DPRNWARE Installation Guide

3DPRNWARE is a portable program, so you will not need to perform an installation, you can simply have the folder containing all the files on your computer. ...

Try the firmware upgrade

Sometimes, to solve some problems of operation of the printer, or simply to add print, you need to perform the firmware upgrade. The firmware with ...

If 3DPRNWARE hangs all boot ’

It could happen that putting the software on a new PC that will not boot immediately giving error to attempt to apertura.Probabilmente the problem is ...

TPE/TPU and rubber printing

For the printing of tpe / TPU and rubber, it is preferable to use an extruder 3mm. With 3DPRN printers you can still print such materials even ...

Driving up-grade: reel support

Let's see how to install the new bobina.Per support First we need to place the anchor of the support block. It is positioned at the front side of the ...

How to get quality media?

To get the supports of good quality and easy removal is appropriate to follow the following tips to set the profile parameters (3DPRNWARE v.3.6 or ...

Using the sensor end thread

If, during a press goes down the power of the extruder material or finish the roll of material, the printer will block the printing process by issuing ...

Error opening file ’ 3D

Sometimes it could happen in the environment 3DPRN-WARE is generated an error in the moment in which it goes on to import a 3D DWG file type or ...

Replace dell ’ extruder nozzle ’

To change the nozzle of the extruder body, it is necessary first of all remove the wire loaded inside the extruder. Once this is done you have to let the hot extruder to a ...

Run the Z-zero

The Z0 tool allows you to set the zero point of the platen. You will need to do this in case it is replaced or removed the ...

Layer sticking out? – Digital Editing Layer

If systematically every few layers, there is printed a projecting, you can be solved by performing the following steps: go under the "Connect" button and select the "Terminal" tab. After that…

How to use form LAN

First you must unplug the printer from the computer and plug it into a USB socket on the LAN module of the same. So we will have a cable ...

Run the Flatness

Flatness The tool allows you to print an object in accordance with any imperfections of the platen and to ensure uniform adherence across the entire ...

Anomalous motion axes

If you experience of abnormal behavior in the handling of the axes, type systematic shift at a certain point of the print in one direction, it could be of values ​​...

Restoring machine parameters

If you have the need to restore the internal parameters of the printer, first note the current values. Go into the terminal ...

You can interrupt and resume printing?

To resume a paused printer must be loaded in the "Print" gcode the press in question. Once this is done you have to physically measure the height in millimeters ...

How do I clean the exterior of an extruder?

To clean the better the visible part of the extruder, it is appropriate to take the first to the temperature of 200 °, in so doing all the material burrs, they will go to ...

As they pull the straps if are slow?

You will notice that the ends of each belt there are media to block them. Such supports are anchored with screws which must be screwed until ...

How do I change the coil material?

In case you want to perform a reel change, the first step is to bring the extruder at a temperature (at least 180 °), then you must rotate the wheel ...

How do I replace an extruder?

In the manual section is present the procedure for replacing the extruder with that of an emergency. Today we will see how to disassemble an extruder to replace it. Let's make sure ...

Can I print multiple objects at once?

One of the many functions provided by the 3DPRN-WARE software, is precisely to be able to set the sequential release where you can split the floor of ...

Menu